Cement bonded particle board with high density 1350 Kg/m³.
The BetonFloor cement bonded particle board is made by two BetonWood panels already coupled togheter in a staggered way to realize a single four stepped side panel; it has a high density (1350 Kg/m³) and a high compression resistance (9.000,00 KPa) and is therefore suitable for use in dry screeds, traditional or raised flooring systems (see Radiant heating systems) and in all places where there is a need for a hard, resistant, fire-certified material (A2 class).
The BetonFloor cement bonded particle board is made by two BetonWood panels already coupled togheter in a staggered way to realize a single four stepped side panel; this makes it excellent for making dry screeds. Made of high density Portland cement (1350 Kg/m³) and debarked pine wood fibers; this coupled guarantees an excellent solution for interventions aimed at obtaining high levels of thermal displacement, thanks to its high density which also makes it suitable for self-supporting dry screeds, radiant floors and stiffening structures.
BetonFloor panels combine the advantageous characteristics of concrete with the characteristics of wood. The structure of the panel is made with wood chips and fragments uniformly mixed with the concrete. The edge surfaces are stepped.
BetonWood cement bonded particle board is also made exclusively with wood from controlled forests in compliance with the FSC directives (Forest Stewardship Declaration).
The cement bonded particle board has so many advantages, including:
• very high compression resistance;
• high resistance to climate change and frost;
• insects and fungi are unable to attack or damage it;
• thanks to its physical and mechanical characteristics, the product is considered one of the best materials for light weight constructions;
• incombustible (A2 according to the DIN 4102 Standard);
• free of formaldehyde and free of asbestos, asbestos etc .;
• free of recycled inks (present in materials with recycled cellulose);
• resistant to atmospheric agents;
• workable with wooden tools;
• high flow rate;
• recyclable, ecological, respects the environment;
• construction material tested and authorized according to the European standards in force.
The BetonFloor cement bonded particle board can be used in:
• radiant heating floor with BetonRadiant system and pre-reinforced floors;
• traditional and ventilated roof with high thermal displacement;
• ceilings, counter-ceilings resistant to fire (A2 class of reaction to fire);
• structure for traditional and elevated floors;
• floor load support;
• high resistance external and internal coatings;
• platforms for counters, platforms and slides;
• exhibition stands and prefabricated boxes;
• road and railway noise barriers;
• escape routes, fire prevention measures.
| thickness (mm) | m³/panel | kg/m² | kg/panel | panels/pallet |
|---|---|---|---|---|
| 20+20 | 0,63 | 52,0 | 34,0 | 28 |
• the delivery of the material is normally carried out by lorries, considering the high mass of the pallets it is advisable for the recipient to have suitable equipment and mechanical lifting means with a minimum capacity of 35/40 quintals for unloading the goods;
• it is advisable to deposit the boards overlapping them one on top of the other and in order to keep them in a horizontal position, with square section supports and a minimum spacing of 80 cm;
• the transport of the single slabs must be done by cutting, never horizontally;
• avoid direct exposure to sunlight and adequately cover the material to avoid excessive accumulation of dust;
• the pallets are equipped with an upper protective plate, which must be repositioned each time above the other boards and ballasted at the top to avoid distortion of the plates below it.
| Characteristics | Values |
|---|---|
| Density kg/m³ | 1350 |
| Fire reaction class according to EN 13501-1 | A2-fl-s1 |
| Thermal conductivity coefficient λD W/(m·K) | 0,26 |
| Specific heat J/(kg·K) | 1880 |
| Vapour diffusion resistance μ | 22,6 |
| Coefficient of linear thermal expansion α | 0,00001 |
| Thick swelling after 24h of permanence in water | 1,5% |
| Air permeability l/min.m² MPa | 0,133 |
| Superficial PH value | 11 |
| Flexural strength σ (N/mm²) | min.9 |
| Transverse tensile strength N (N/mm²) | min.0,5 |
| Shear resistance τ (N/mm²) | 0,5 |
| Elasticity module Ε (N/mm²) | 4500 |
| Resistance to distributed load kPa | 9000 |
| Concentrated load resistance kN | 9 |
| Thickness (mm) | Distance (cm) | |||||||
|---|---|---|---|---|---|---|---|---|
| 1,00 | 1,50 | 2,00 | 2,50 | 3,00 | 4,00 | 5,00 | 6,00 | |
| 40 | 178 | 148 | 130 | 117 | 108 | 95 | 85 | 79 |
| Thickness (mm) | Frequency (hz) | |||||
|---|---|---|---|---|---|---|
| 100 | 200 | 400 | 800 | 1600 | 3150 | |
| 40 | 23,5 | 28,7 | 34,1 | 39,6 | 45,1 | 50,6 |
The BetonWood cement bonded particle board is coupled with the best natural and non-natural insulating materials (wood fiber, cork, extruded and expanded polystyrene), to obtain specific design solutions suitable for the different thermal and acoustic insulation needs...
The BetonRadiant modular radiant system consists of a high density cement bonded particle board (1350 kg/m³), and can be supplied coupled with insulating materials such as cork, wood fiber, or polystyrene. Traditional or raised radiant heating floors...
BetonTherm is the system for thermo-acoustic coatings with high mechanical resistance and high thermal displacement, for both internal and external insulation and suitable for both traditional constructions and dry wood systems...
BetonWood also offers a wide range of accessories for the installation of its main products. In this section you will find accessories for dry screeds, radiant screeds, internal and external walls, roofs, attics, thermal insulating coats...